Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Sherman Oaks: What to Know First

We provide independent Olympia Chimney chimney cap and crown service in Sherman Oaks, typically completing standard cap replacements and crown repairs within one visit after inspection. Every job starts with a written price before work begins, backed by our 365-Day Done Right Promise. You’ll see camera footage of the damage, get a line-item quote, and review the warranty terms before anyone picks up a tool. This page is for Sherman Oaks homeowners who already have an Olympia Chimney cap or crown installed, or are comparing Olympia Chimney products against other brands we service. Call (424) 414-6048 to schedule your free estimate.

Call (424) 414-6048

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney 304 stainless single-flue caps in the 1300 series develop weld-seam fatigue at the corner joints after 7-10 years in Sherman Oaks’ Santa Ana wind cycles. The seam cracks aren’t visible from the ground, but water enters the flue and stains the firebox. We pull the cap, inspect the weld integrity with a borescope, and either re-weld at our shop or source a replacement through our Haven buying network.
• Olympia Chimney multi-flue caps in the 2000 series use a mesh screen that’s factory-crimped at a tighter gauge than DuraFlex or Gelco equivalents. The tighter mesh traps coastal salt and Ventura Boulevard corridor particulate, accelerating rust-through from the inside out. We document the mesh condition with photos, then install either an OEM Olympia Chimney replacement screen or a Famco aftermarket equivalent with equivalent spark-arrestor rating but wider cleanout access.
• Olympia Chimney crown-mounted caps in the 1500 series rely on a factory caulk bed that cures harder than HeatShield crown coating. In Sherman Oaks’ thermal swings, the caulk separates from the crown concrete while the cap itself stays sound. We remove the cap, grind the old bedding to bare concrete, apply a flexible polymer base, and re-bed the cap with a joint that moves with the crown.
• Olympia Chimney galvanized economy caps show flaking zinc at the drip edge within 4-6 years, faster than the manufacturer spec suggests for inland climates. Sherman Oaks sits in a microclimate pocket where marine layer moisture lingers against north-facing chimney faces. We flag this during camera inspection and quote a 304 stainless upgrade before the steel substrate pits.
• Olympia Chimney custom wind-directional caps use a rotating collar bearing that seizes when homeowners in the hills above Beverly Glen neglect the annual lubrication point. The cap locks in one position and becomes a wind scoop instead of a wind deflector. We free the bearing, replace it with a sealed unit from our Copperfield supply line, and show the owner the maintenance interval in writing.

Our Olympia Chimney Chimney Cap & Crown Process

1. 1
   Call and schedule. A live person answers, checks availability, and notes your Olympia Chimney model if you know it. We don’t use web forms or voicemail queues.
2. 2
   NFPA 211 Level 2 inspection on arrival. Our tech runs a camera down the flue and photographs the cap or crown from the roof. You see what we see on the tablet before we discuss price. The camera doesn’t lie, and neither does the written quote.
3. 3
   Parts decision with options. We stock common Olympia Chimney caps and carry DuraFlex, HeatShield, Gelco, Famco, and Copperfield equivalents. If your cap is under manufacturer warranty, we explain what’s covered and what isn’t, then quote both OEM and quality aftermarket paths.
4. 4
   Written price, written scope, written warranty. Haven Standard Clause 1 requires all three before work starts. No exceptions. You sign, we start.
5. 5
   Repair or replacement with photo documentation. Crown work gets a moisture-meter reading after cure. Cap installs get a draft-test verification. Every photo and reading goes into your record under Haven Standard Clause 4.
6. 6
   Cleanup, walkthrough, and archived record. We text you the photo link before leaving. The 365-Day Done Right Promise applies automatically. No paperwork to hunt for later.

Before

After

What Olympia Chimney Chimney Cap & Crown Costs in Sherman Oaks

These are real Sherman Oaks prices for Olympia Chimney products, not national estimates. Your exact quote comes after inspection, in writing, with no obligation. Call (424) 414-6048 for your free estimate.

Why Sherman Oaks Homeowners Call Emberly Chimney Cleaners Sherman Oaks for Olympia Chimney Work

We’ve inspected over 38,000 chimneys since 2009, and a significant share of the cap and crown jobs in Sherman Oaks involve Olympia Chimney hardware. Corrine Halstead and our crew know the product line’s failure patterns from hands-on work, not a dealer manual. When an Olympia Chimney part is backordered, we have DuraFlex, HeatShield, Gelco, Famco, and Copperfield alternatives in our Haven buying network, so you’re not waiting on factory lead times. Every tech is background-checked, uniformed, and licensed, with a text-on-the-way system so you know who’s arriving. The 365-Day Done Right Promise means if the cap leaks or the crown cracks through our work, we make it right without a second invoice.

FAQs